LS-T30
Control Reference Guide...........4
Placement .................................7
Connecting to a TV....................8
Listening to TV ..........................9
TV Speaker System
Instruction Manual
Using a
TV Remote Controller.............. 11
Playing via
Bluetooth Connection..............12
Troubleshooting.......................13
Supplied Accessories..............15
Thank you for purchasing an Onkyo product. Please read this
manual thoroughly before making connections and plugging in
your new Onkyo product.
Following the instructions in this manual will enable you to
obtain optimum performance and listening enjoyment from your
new product.
Please retain this manual for future reference.
Safety precautions
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
≥
≥
Subwoofer is designed to be used in the upright vertical position
only. Do not use it in the horizontal or tilted position.
If the unit is used near a turntable, CD player or DVD player,
howling or slipping of sound may occur. To prevent this, move
the unit away from the turntable, CD player or DVD player,
otherwise lower the unit’s output level.
-
This device complies with Industry Canada licenceexempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Use with a TV set
In general, Braun tubes used for color television sets, etc. are extremely
sensitive and can be affected even by the magnetism of the earth. If a
speaker system is used near them, therefore, discoloring or distortion of
pictures will occur. These speakers are not provided with magnetic
shielding. If discoloration or distortion occurs, move the speakers apart
from the television set.
This transmitter must not be co-located or operated in conjunction with
any other antenna or transmitter.
RF Exposure Compliance
Input Signal Warning
This equipment complies with FCC/IC radiation exposure limits set forth
for an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC
radio frequency (RF) Exposure rules. This equipment has very low levels
of RF energy that it deemed to comply without maximum permissive
exposure evaluation (MPE). But it is desirable that it should be installed
and operated keeping the radiator at least 20 cm or more away from
person’s body (excluding extremities: hands, wrists, feet and ankles).
The speakers can handle the specified input power when used for normal
music reproduction. If any of the following signals are fed to them, even if
the input power is within the specified rating, excessive current may flow
in the speaker coils, causing burning or wire breakage:
1
2
3
Interstation noise from an untuned FM radio.
Sound from fast-forwarding a cassette tape.
High-pitched sounds generated by an oscillator, electronic musical
instrument, and so on.
4
5
6
Amplifier oscillation.
For Canadian Models
NOTE:
CAN ICES-3 B/NMB-3 B
For models having a power cord with a polarized plug:
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
Special test tones from audio test CDs and so on.
Thumps and clicks caused by connecting or disconnecting audio
cables (Always turn off your amplifier before connecting or
disconnecting cables).
7
Microphone feedback.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
-
Par la présente, Onkyo Corporation déclare que l’appareil LS-T30 est
conforme aux exigencies essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.
Por la presente, Onkyo Corporation, declara que este LS-T30 cumple con
los requisites esenciales y otras exigencias relevantes de la Directiva
1999/5/EC.
Con la presente Onkyo Corporation dichiara che questo LS-T30 è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.
Hiermit erklärt Onkyo Corporation, dass sich das Gerät LS-T30 in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Hierbij verklaart Onkyo Corporation dat het toestel l LS-T30 in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Härmed förklarar Onkyo Corporation att denna LS-T30 följer de väsentliga
kraven och andra relevanta stadgar i Direktiv 1999/5/EC.
С настоящето, Onkyo Corporation, декларира, че LS-T30 е в
съответствие със съществените изисквания и другитеприложими
разпоредби на Директива 1999/5/EC.
Onkyo Corporation tímto prohlašuje, že LS-T30 splňuje základní
požadavky a všechna příslušná ustanoveni Směrnice 1999/5/ES.
Undertegnede Onkyo Corporation erklærer herved, at følgende udstyr
LS-T30 overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
For British models
Replacement and mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified service personnel.
-
-
-
-
IMPORTANT
The wires in the mains lead are coloured in accordance with the following
code:
Blue:
Brown:
Neutral
Live
As the colours of the wires in the mains lead of this apparatus may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows: The wire which is coloured blue must be
connected to the terminal which is marked with the letter N or coloured
black. The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse needs to be
replaced, the replacement fuse must approved by ASTA or BSI to
BS1362 and have the same ampere rating as that indicated on the plug.
Check for the ASTA mark or the BSI mark on the body of the fuse. If the
power cord’s plug is not suitable for your socket outlets, cut it off and fit a
suitable plug. Fit a suitable fuse in the plug.
-
-
-
-
-
-
Käesolevaga kinnitab Onkyo Corporation seadme LS-T30 vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele
teistele asjakohastele sätetele.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ Onkyo Corporation ΔΗΛΩΝΕΙ
ΟΤΙ LS-T30 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ
ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Ar šo Onkyo Corporation deklarē, ka LS-T30 atbilst Direktīvas 1999/5/EK
būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Šiuo Onkyo Corporation deklaruoja, kad šis LS-T30 atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
A Onkyo Corporation ezzennel kijelenti, hogy a LS-T30 típusú beren-dezés
teljesíti az alapvető követelményeket és más 1999/5/EK irányelvben
meghatározott vonatkozó rendelkezéseket.
Niniejszym Onkyo Corporation deklaruje że LS-T30 jest zgodny z
zasadniczymi wymaganiami i innymi właściwymi postanowieniami
Dyrektywy 1999/5/EC.
Eu, Onkyo Corporation, declaro que o LS-T30 cumpre os requisitos
essenciais e outras provisões relevantes da Directiva 1999/5/EC.
Prin prezenta, Onkyo Corporation, declară că aparatul LS-T30 este în
conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente ale
Directivei 1999/5/CE.
Onkyo Corporation týmto vyhlasuje, že LS-T30 a spĺňa základné
požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
Onkyo Corporation izjavlja, da je ta LS-T30 v skladu z bistvenimi
zahtevami in drugimi relevantnimi določili direktive 1999/5/ES.
Onkyo Corporation vakuuttaa täten että LS-T30 tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin
muiden ehtojen mukainen.
Hér með lýsir Onkyo Corporation því yfir að varan LS-T30 er í samræmi við
grunnkröfur og aðrar kröfur sem gerðar eru í tilskipun 1999/5/EC.
Onkyo Corporation erklærer herved at denne LS-T30 er i
overensstemmelse med vesentlige krav og andre relevante bestemmelser
I direktiv 1999/5/EC.
For European Models
WEEE
-
-
-
Declaration of Conformity
We declare, under our sole responsibility, that this
product complies with the standards:
-
-
Safety
-
Limits and methods of measurement of radio
disturbance characteristics
-
-
-
-
-
-
Limits for harmonic current emissions
Limitation of voltage changes, voltage fluctuations and flicker
RoHS Directive, 2011/65/EU
Hereby, Onkyo Corporation, declares that this LS-T30 is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
-
-
-
Speaker Precautions
Placement
≥
The subwoofer cabinet is made out of wood and is therefore
-
-
sensitive to extreme temperatures and humidity, do not put it in
locations subject to direct sunlight or in humid places, such as
near an air conditioner, humidifier, bathroom, or kitchen.
Do not put water or other liquids close to the speakers. If liquid is
spilled over the speakers, the drive units may be damaged.
Speakers should only be placed on sturdy, flat surfaces that are
free from vibration. Putting them on uneven or unstable surfaces,
where they may fall and cause damage, will affect the sound
quality.
≥
≥
-
Ovime Onkyo Corporation, potvrđuje da je LS-T30 u suglasnosti sa
osnovnim zahtjevima i ostalim relevantnim odredbama Direktive
1999/5/EC.
3
Control Reference Guide
Main unit
INPUT button: Switches the input
source. Each time the button is pressed,
input modes are switched in order of TV#
USB (North American models) #
Bluetooth # ....
Status indicators: Displays the sound
mode, volume, and subwoofer level.
Right channel speaker
*
Also, switches the power on/standby. Press
and hold for approximately 3 seconds to place
the device into Standby. Press once to turn the
power on.
VOLUME i/j buttons
SOUND MODE button: Use this button to
select the desired sound mode for the
playback audio. (# P10)
Dolby indicator: Lights when the digital
audio input signal is Dolby Digital.
Left channel speaker
Input source indicator: Lights in
accordance with the input source. The
indicator lights in white for TV, yellow for
USB (North American models), and blue for
Bluetooth.
Bottom of the unit
Subwoofer: Plays sub-bass frequencies.
4
Control Reference Guide
Rear of the unit (terminals)
OPTICAL jack: Makes a digital connection
ANALOG jack: Makes an analogue
to the TV with the supplied optical digital
connection with the TV using the supplied
stereo mini plug cable.
audio cable.
are used depending on
the audio outputs available on your TV.
COAXIAL jack: Makes a digital connection
to the TV using a coaxial cable
(sold separately).
DC IN terminal: Connects the supplied
AC adapter.
USB port: (North American models)
Connects a USB flash memory.
(Others) This port is used for service
purposes only. Do not use it.
5
Control Reference Guide
North American models
Others
Remote controller
This manual outlines procedures using the
remote controller.
When using the remote controller for the first
time, remove the insulation sheet.
ON/STANDBY button: Switches the power
on/standby.
SUBWOOFER i/j buttons: Adjust the
subwoofer level.
SOUND MODE button: Use this button to
select the desired sound mode for the
playback audio.
Use a CR2025 lithium coin battery for battery
replacement.
INPUT buttons: Switches the input source.
VOLUME i/j buttons
Positive (i) side
MUTING button
USB operation buttons (North American
models): Allows operation when the input
source is USB.
plays or pauses playback.
return to
Remote control sensor
the start of the file being played. Press twice
to return to the previous file.
next file.
skip to the
20°
Approx.
5 m (16 ft)
30°
30°
20°
6
Placement
1. Affix the cushioning pads to the bottom of the
TV stand.
Using the supplied cushions will allow you to
limit the effect of vibrations on the TV.
Wrap the TV in a blanket or soft cloth to
avoid damage during installation. Installation
should be performed by at least two people.
When the supplied cushions and the feet of
the TV do not match, cut and shape the
cushions for use as needed.
The illustration shows an example of
placement. Mount the unit on a firm surface
such as the top of a low board. Also, subwoofer
is located on the bottom side of the unit. Please
take extra care on setting.
2. Place the unit on top of the low board.
The unit is extremely heavy. Be very careful
not to trap your fingers when mounting it.
TVs meeting the following requirements may be
placed on the unit.
0 Weight: 60 kg (132.2 lbs) or less
0 Width of TV stand: 900 mm (35-7/16") or
less
Mount the TV so that it does not protrude
from the top face of the unit. If the TV stand
protrudes from the top face of the unit, the
TV may tip over and cause injury. Also, for
TV tip-over/fall prevention measures, see the
TV owner’s manual.
0 Depth: 360 mm (14-3/16") or less
Mountable area
0 If the unit vibrates after placement, mount
the supplied vibration prevention cushions
under the feet of this unit, and adjust so that
it does not vibrate.
0 Onkyo is not responsible for accidents or
damage caused by improper installation,
improper cushion attachment, improper use
or natural calamity, etc.
7
Connecting to a TV
If there is the OPTICAL jack on the TV
being used (illustrated above)
If there is no OPTICAL jack on the TV
being used
Make a digital connection to the TV with the
supplied optical digital audio cable. Connect the
AC adapter/power cord into the DC IN on the
unit, and then connect the other end of the
power cord into an electrical outlet.
Connect either of the following.
∫ Make an analogue connection with the TV
using the supplied stereo mini plug cable.
Important :
Depending on the TV to be used with this
unit, the sound coming through the TV’s
built-in speakers can be out of sync with the
sound coming through the unit. Be sure to
turn off the built-in speaker output on your TV
before using the unit. Perform the same
procedure when also making connections
using the stereo mini plug cable or coaxial
cable.
∫ Make a digital connection to the TV using a
coaxial cable (sold separately).
8
Listening to TV
Basic operations
To adjust the subwoofer level
1. Turn on the TV.
Allows to adjust the subwoofer level by 1 step in
the j10 to i10 range while listening to the
sound. The default setting is 0. Also, the
subwoofer level is set to individual levels for
each different SOUND MODE.
Auto Power On is turned on by default, and
so power to the unit turns on automatically.
The input source automatically switches to
TV, and audio from the TV is played.
0 The input source switches to TV, and the
input source indicator lights in white.
1. Press SUBWOOFER i/j.
To cancel Auto Power On: press and hold
on the unit, and then press and hold
while continuing to press
. The input
source indicator flashes twice (white) to
indicate that this setting is now off.
0 Repeating this procedure switches
between on/off. The indicator flashes
once to indicate that this setting is now
on.
The status indicators (white) indicate the
subwoofer level.
Volume: “Standard”
0 When this setting is off, press
on the power to the unit, and then press
to switch the input source to TV.
to turn
To mute the sound
1. Press MUTING.
To adjust the volume of this unit
Allows to adjust the volume by 1 step in the 0 to
35 range.
1. Press VOLUME i/j.
The status indicator flashes when the audio is
muted. Press again to cancel muting. Muting
will also be canceled when the volume is
changed or the power is turned off and on.
0 When using buttons on the unit, press
and
cancel muting.
at the same time. Press again to
The status indicators (white) indicate the
volume level.
Volume: “Middle”
9
Listening to TV
Change the desired sound quality
(SOUND MODE)
You can switch the sound mode of input sound
as desired.
Auto Standby function:
If there is no audio input and no operation of
the unit has been performed for some time,
the power will automatically enter standby
mode as Auto Standby is on by default. The
time taken to enter standby mode depends
on the connected cables or the input source.
0 Connecting with the optical digital audio
cable or coaxial cable: 2 hours
(5 minutes when power to the TV is off)
0 Connecting with the stereo mini plug
cable: 5 minutes
0 Bluetooth/USB (North American models):
5 minutes
1. Press SOUND MODE button.
The sound modes are switched in the
following order each time this button is
pressed. The status indicator lights (orange)
indicate the current mode.
(Standard)
Play files with a good balance from low
through to high frequencies. This is the
standard mode with neutral settings.
To cancel this function, press and hold
the unit, and then press and hold while
continuing to press . The input source
indicator flashes twice (white) to indicate that
this setting is now off.
0 Repeating this procedure switches
between on/off. The indicator flashes
once to indicate that this setting is now
on.
on
(Surround)
Creates a richer sound field, provides
realistic sound movement and amplifies
bass sounds. Ideal for watching movies.
(Stereo)
Suitable for listening to music. Playback
music with pure quality similar to the
original sound.
(Voice)
Play files with voice clearly. Ideal when
watching the news or documentary
programmes.
Switch audio in sound-multiplex
programmes
This can be set only when the audio signal is
Dolby Digital. Press and hold the SOUND
MODE button on the remote controller for
approximately 3 seconds. Pressing and holding
switches the source in the following order.
Main: The input indicator (white) flashes
once.
Secondary: The input indicator (white)
flashes twice.
MainiSecondary: The input indicator
(white) flashes three times.
10
Using a TV Remote Controller
2. While the input source indicator is flashing,
Preprogrammed feature
press any button on the TV remote controller
3 times while aiming it at the remote control
signal sensor of the unit.
The unit has been preprogrammed so that the unit
can be operated using your TV remote controller.
Volume control and muting(*) operations can be
performed with this feature. If you want to use other
functions or cannot operate the unit with your TV
remote controller, you can use the learning function
(described below) to enable these features.
The indicator flashes twice (white) to indicate
that this was successfully configured. After
this is set, pressing the button on the TV
remote controller will enable ON/STANDBY
operation on the unit.
The learning function enables the following unit
functions to be operated with your TV remote
controller. Press and hold the following buttons
To cancel this feature, press and hold
approximately 3 seconds while continuing to
press and hold on this unit The input source
indicator will flash (white) for 10 seconds. Do not
operate the unit during this time. Afterwards, it
will flash 3 times to indicate that this feature has
been cancelled. Perform the same procedures to
use the TV remote controller again.
for
instead of
in step 1.
- VOLUME i:
- VOLUME j:
- MUTING:
- INPUT:
- SOUND MODE:
and
and
and
*
The mute state can be turned over each time you
press the Mute button on your TV remote controller.
In such case, you can synchronize the mute status of
the unit and the TV by pressing and holding the Mute
button on your TV remote controller.
To prevent incorrect operation:
The unit is preprogrammed to support a large
number of TV remote controllers. For this
reason, using remote controllers other than
that supplied with the unit and TV remote
controllers may result in unexpected operation.
To prevent incorrect operation, press and
Learning function
hold
on the unit, and then press and hold
for 3
The unit is set so that signals emitted from each
button on your TV remote controller control
specific operations.
while continuing to press
seconds. The input source indicator will flash
(white) for 10 seconds. During this time, aim
the TV remote controller toward the unit and
press either the volume button or mute
button once. The input source indicator will
flash twice (white), which indicates that the
unit will not accept signals emitted when
buttons are pressed on remote controllers
other than the supplied remote controller or
the TV remote controller.
*
It is recommended to select buttons that do not
prevent TV operation when assigning the functions
to your remote controller. Signal of some types of
remote controller may not be received by the unit.
E.g.) To assign the unit's ON/STANDBY
function to the TV remote controller:
1. Press the
approximately 3 seconds while pressing and
holding the button. The input source
indicator (white) flashes for 10 seconds.
button on the unit for
0 Controlling function may not be set to
some TV remote controller.
11
Playing via Bluetooth Connection
Approx.10 m (33 ft)
You can wirelessly enjoy music files stored in a
smartphone or other Bluetooth-enabled device.
The coverage area is 10 meters (33 feet).
Playing sound of the
Bluetooth-enabled device
1. Press
2. Press
to turn on the unit.
to switch the selector to Bluetooth.
Pairing
The input source switches to Bluetooth, and
the input source indicator lights in blue.
3. Play music files by after connecting the
Bluetooth device.
Pairing is necessary when using the
Bluetooth-enabled device for the first time.
Before starting the procedure, learn how to
enable the Bluetooth setting function and to
connect with other devices on the
Bluetooth-enabled device.
1. Press
2. Press
0 If the volume setting on the
Bluetooth-enabled device is low, the
sound will not be output from this unit.
0 Due to the characteristics of Bluetooth
wireless technology, the sound produced
on this unit may slightly be behind the
sound played on the Bluetooth-enabled
device.
to turn on the unit.
to switch the selector to Bluetooth.
To register other Bluetooth devices: Turn
on the power to the unit, switch the input to
Bluetooth, and then press and hold
to
start pairing on the unit. Next, select the unit
(Onkyo LS-T30) on some other Bluetooth
device to make a connection.
0 Up to 16 Bluetooth devices can be saved
with the unit.
The unit begins pairing, and the input source
indicator on the unit will flash quickly (blue).
The pairing mode will be cancelled after 30
seconds. During this time, perform the
following operation. The indicators will flash
slowly indicating that this has been
cancelled.
0 When using buttons on the unit, press
and hold
.
3. Select the unit (Onkyo LS-T30) after it
displays on the screen on the Bluetooth
device. After a short time, the input source
indicator will light (blue), and the devices are
now paired.
0 If a passcode (password, passkey or PIN
code) is requested, enter "0000".
0 Devices should be in close proximity
when pairing.
12
Troubleshooting
There’s no sound, or it’s too small
0 Make sure that all audio connecting plugs
are pushed in all the way.
0 Make sure that the input of device is
connected properly.
0 When the status indicator flashes in white,
the muting is enabled. Press MUTING button
on the remote controller or the
Before starting the procedure
Problems may be solved by simply turning
the power on/off or disconnecting/connecting
the power cord, which is easier than working
on the connection, setting and operating
procedure. Try the simple measures on both
the unit and the connected device.
VOLUME i/j buttons on the remote
controller or the unit to disable the muting.
0 Make sure that none of the connecting
cables are bent, twisted, or damaged.
0 Audio is output through only one type of
connection. When multiple terminals are in
use, the priority of audio output is given in
the order of the OPTICAL terminal,
COAXIAL terminal, and ANALOG terminal.
∫ Resetting the unit
Resetting the unit to the status at the time of
shipment may solve the problem. Reset the unit
with the following procedure.
Press and hold the
the power is on, and then press and hold
while continuing to press for 10 seconds.
button on the unit when
When reset is complete, the INPUT source
indicator and all status indicators light and the
unit automatically enters the standby mode.
Noise can be heard
0 Do not bind the power cord, connection
cables and other audio cables with a band.
0 An audio cable may be picking up
Can’t turn on the unit
0 Make sure that the power cord is properly
plugged into the wall outlet.
interference. Try repositioning your cables.
0 Unplug the power cord from the wall outlet,
wait 10 seconds or more, then plug it in
again.
The remote controller doesn't work
0 Make sure that the battery is installed with
the correct polarity.
0 Make sure that the remote controller is not
too far away from the unit, and that there’s
no obstruction between the remote controller
and the unit’s remote control sensor.
0 Make sure that the unit is not subjected to
direct sunshine or inverter type fluorescent
lights. Relocate if necessary.
The unit turns off unexpectedly
0 The unit will automatically enter standby
mode when Auto Standby launches.
The sound stops suddenly, or stops
during playback
0 If the remote controller does not work the
first time after purchase or if it has not been
used for a long period of time, the battery
may have become flat and the remote
controller will not operate. Try the following
methods.
- Press and hold the VOLUME jbutton on
the remote controller for some time
(10 seconds or more). (try this several
times)
0 The protective circuits of the unit may be
operating. Unplug the power cord from the
wall outlet immediately. Check that all cables
are connected and that the input source is
correct, and leave the power cord unplugged
for 5 minutes. Plug the power cord in again
and turn the unit power on. If the sound still
cuts out, unplug the power cord and contact
your Onkyo dealer.
0 If smoke, smell or abnormal noise is
produced by the unit, unplug the power cord
from the wall outlet immediately and contact
your Onkyo dealer.
- Remove the button cell, wipe it with a
clean cloth and insert it again.
13
Specifications
Playing USB Memory (North American models)
0 The unit supports USB memory formatted using
FAT12, FAT16 and FAT32 file system.
0 The unit is compatible with WAV playback and
following audio format is supported.
Format: Microsoft PCM format
Rated Output Power (FTC):
Front speaker:
(North American) 12.5 W minimum
continuous power per channel, 4 ohm
loads, 2 channel driven at 1 kHz, with a
maximum total harmonic distortion of 1%
Subwoofer:
Number of channels: 1 or 2 channels
Sampling frequency: 32 to 48 kHz
(North American) 25 W minimum
continuous power, 4 ohm loads, 1 channel
driven at 80 Hz, with a maximum total
harmonic distortion of 1%
Rated Output Power (IEC):
Front speaker:
Quantization bit width: 8 or 16 bit depth
RIFF chunk: format chunk (without extended),
data chunk
0 You can play WAV files stored on the root folder
only. WAV files stored on the other folders cannot
be played on this unit.
0 The unit supports USB flash drives only. Note,
however, that playback may not be possible with
some USB flash drives.
(Others) 2chk12.5 W at 4 ohms, 1 kHz 1ch
driven of 1%
Subwoofer:
(Others) 1chk25 W at 4 ohms, 80 Hz 1ch
driven of 1%
Disclaimer
0 The unit contains a microcomputer for signal
processing and control functions. In very rare
situations, severe interference, noise from an
external source, or static electricity may cause it to
lock up. In the unlikely event that this happens,
unplug the power cord from the wall outlet, wait at
least five minutes, and then plug it back in.
If it doesn’t work properly, please try resetting.
Frequency response:
Power Supply:
Power Consumption:
20 Hz - 20 kHz
AC100 - 240 V, 50/60 Hz
17 W
Stand-by Power Consumption:
(North American) 0.40 W
(Others) 0.45 W
Dimensions (WkHkD):
905 mmk95 mmk400 mm
(35-5/8"k3-3/4"k15-3/4")
10.4 kg (22.9 lbs.)
∫ Trademarks and Licensing
Weight:
Audio inputs
Digital input:
OPTICAL: 1
COAXIAL: 1
(North American) USB: 1
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
Analog Stereo Input:
Bluetooth:
Ø 3.5 mm mini
Version: 2.1iEDR
Profile: A2DP GAVDP
Speaker unit (None magnetic shielding)
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, & DTS and the Symbol
together are registered trademarks, and
DTS Studio Sound is a trademark of DTS, Inc.
(C)DTS, Inc. All Rights Reserved.
Front speaker:
Subwoofer:
6.5 cm (2-1/2") Cone k4
16 cm (6-1/2") Cone k1
0 Design and specifications are subject to
change without notice.
The BluetoothR word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use
of such marks by Onkyo is under license.
Other trademarks and trade names are those of their
respective owners.
14
Supplied Accessories
Make sure you have the following items before
use.
0 The number in parenthesis indicates the
quantity.
0 In catalogs and on packaging, the letter at
the end of the product name indicates the
color.
AC adapter (1)
Power cord (1)
Remote controller (1)
RC-894S (North
American models)
RC-895S (Others)
Optical digital audio
cable 1.5 m (5 ft.) (1)
Ø 3.5 mm stereo mini
plug cable (1)
Cushion (8)
(attach to the bottom
face of the TV)
Vibration prevention
cushions (4)
15
Onkyo Corporation
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku, OSAKA 541-0041, JAPAN
The Americas
Onkyo U.S.A. Corporation
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
For Dealer, Service, Order and all other Business Inquiries:
Tel: 201-785-2600 Fax: 201-785-2650
For Product Support Team Only:
1-800-229-1687
Europe
Onkyo Europe Electronics GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4208-213
Onkyo Europe Electronics GmbH (UK Branch)
Meridien House, Ground floor, 69 - 71 Clarendon Road, Watford, Hertfordshire, WD17 1DS, United Kingdom
Tel: +44 (0)8712-00-19-96 Fax: +44 (0)8712-00-19-95
China
Onkyo China Limited (Hong Kong)
Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.
Tel: 852-2429-3118 Fax: 852-2428-9039
Onkyo China PRC (Mainland)
1301, 555 Tower, No.555 West NanJing Road, Jing’an District, Shanghai, China 200041,
Tel: 86-21-52131366 Fax: 86-21-52130396
Asia, Oceania, Middle East, Africa
Please contact an Onkyo distributor referring to Onkyo SUPPORT site.
The above-mentioned information is subject to change without prior notice.
Visit the Onkyo web site for the latest update.
F1408-0
SN29401856
(C) Copyright 2014 Onkyo Corporation Japan. All rights reserved.
*
2
9
4
0
1
8
5
6
*
|