D-205F
Connection
Speaker System
Turn the sound volume to the minimum and turn OFF the
amplifier power switch (POWER) before connecting the speaker
cables.
The nominal impedance of this speaker system is 6
amplifiers capable of handling this impedance.
Use the supplied speaker cables to connect between speaker 's
binding posts and the amplifier's speaker terminals as illustrated
below.
Thank you for your purchase of the Onkyo speaker system.
Please read this manual thoroughly before using it.
Following the instructions in this manual will enable you to
obtain optimum performance and listening enjoyment from
your new speaker system.
Ω. Use only
Please retain this manual for future reference.
Connect the speaker cables securely to the terminals, with the
core wires twisted properly. In this case, make sure that the core
wires do not touch each other. Note that a short circuit in core
wires may result in damage to the amplifier.
Connect the Right and Left speakers (as viewed from the
listening position) to the amplifier's corresponding Right and Left
speaker terminals.
Before using this unit
The speaker cabinet is made of wood and is therefore
sensitive to extreme temperatures and humidity. Avoid
placing the speaker systems in locations subjected to direct
sunlight, or in smokey or in humid places, such as near an
air conditioner, humidifier, bathroom, or kitchen. Doing so
may result in damage to the speaker.
Place the unit on a rigid, level surface. Placing it on a
slanted surface or weak base not only may cause the unit to
fall, but also results in decreased sound quality.
Be sure to turn off your amplifier before connecting the
speaker system. Connecting them with the amplifier's power
on may result in damage to the amplifier or the speaker
system.
Loosen the screws.
Insert the speaker wires
to the connection.
Fasten the screws
securely again.
Keep water or other liquids away from the unit. If water is
spilled into the unit, not only the unit but also the speakers
themselves may be damaged.
Name and function of each part
165mm
235mm
Cabinet
Grille plug holes
Input
Terminal
Tweeter
Grille
R
L
–
+
–
+
Woofer
Bass-reflex port
Bass-reflex port
268mm
195mm
(R )
(L)
R
L
Precaution on use
+
–
–
+
This speaker system can handle the specified input power
when it is used for ordinary music reproduction. If the
following abnormal signals are fed to the speaker, however,
an overcurrent may flow in the internal circuits, causing
burning or breakage of the wires even if the input power is
below the specified rating.
Amplifier's speaker output terminals
1. Noise produced when FM station is not tuned in
2. Sound produced when fast-forwarding cassette tape
deck
3. High-frequency sound generated by an oscillator, an
electronic musical instruments, etc.
4. Oscillating amplifier signals
5. Special test signals produced by audio checking CD, etc.
6. Sound produced when connecting or disconnecting audio
connection cables (Always turn off the amplifier’s power
before connecting or disconnecting cables.)
Before turning on the amplifier's power switch:
Make sure that the positive (+) and negative (–) speaker
cables do not contact each other. Otherwise, a short-circuit
may occur, causing damage to the amplifier.
Be sure to connect the speaker cables with correct polarity
(connect the speaker's positive (+) and negative (–) binding
posts with the amplifier's corresponding speaker terminals).
Reversed polarity results in impaired bass-range reproduc-
tion, causing mislocalization of the sound image. Also, be
sure to connect the Right and Left speakers with the amplifi-
er's corresponding speaker terminals.
7. Howling when a microphone is used
Do not place magnetic objects such as screwdrivers and iron
parts near the speaker system since they use speakers with
strong magnets. Otherwise, the objects may be attracted,
causing injury or damaging the diaphragm.
Pull lightly on the speaker cables to ensure that they are
connected firmly.
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi,
OSAKA 572-8540, JAPAN
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
HOMEPAGE
E
|